By joining you will help ensure that we can continue to provide this service
JOIN HERE!
Just got a 1976 R60/6
Just got a 1976 R60/6
Any tips or advice on how I should go about checking everything over?
- schrader7032
- Posts: 9061
- Joined: Fri Oct 27, 2006 3:00 am
- Location: San Antonio, TX
- Has thanked: 3 times
- Been thanked: 36 times
Re: Just got a 1976 R60/6
'78 R100/7 '69 R69S '52 R25/2
Fast. Neat. Average. Friendly. Good. Good.
- srankin
- Posts: 1085
- Joined: Fri Jul 14, 2017 8:45 pm
- Location: Spencerport, NY USA
- Been thanked: 21 times
Re: Just got a 1976 R60/6
Other than that, what Kurt suggested is the start. St.
- Flx48
- Posts: 263
- Joined: Sun Oct 25, 2020 3:11 pm
- Location: NW CT
- Has thanked: 2 times
- Been thanked: 7 times
Re: Just got a 1976 R60/6
And if thinking you many be using the bike much, or keeping it for a while, go ahead and start documenting what and when you perform any of the above maintenance, for future reference.
It's very helpful for determining what we need to do in the future; and the reason we all wish we'd started doing so much earlier in the past...
Best-
George
- cbclemmens
- Posts: 223
- Joined: Sun Apr 25, 2021 2:21 pm
- Location: Apollo, PA
- Been thanked: 6 times
Re: Just got a 1976 R60/6
After you change the fluids and filters, pull the plugs and crank the engine over in case gas, oil or other fluids leaked into the cylinders. (ST will tell you to hook up the plugs and ground them first. I would add cover them with a clean rag so you don't spit raw gas onto them.) Then put in new plugs.
Craig
- srankin
- Posts: 1085
- Joined: Fri Jul 14, 2017 8:45 pm
- Location: Spencerport, NY USA
- Been thanked: 21 times
Re: Just got a 1976 R60/6
Was the basement dry? If not, the list of things to look for goes up. Cast iron cylinders can rust for example.
Where are you located perhaps I could give a hand? St.
- schrader7032
- Posts: 9061
- Joined: Fri Oct 27, 2006 3:00 am
- Location: San Antonio, TX
- Has thanked: 3 times
- Been thanked: 36 times
Re: Just got a 1976 R60/6
'78 R100/7 '69 R69S '52 R25/2
Fast. Neat. Average. Friendly. Good. Good.
Re: Just got a 1976 R60/6
The basement was dry, and honestly the bike looks in pretty fabulous shape (considering).
The previous owner seemed to be fairly meticulous on maintenance (according to the wife), and the paperwork I received came with some detailed notes he had made over the years. So I am very hopeful.
I have all winter to tinker / restore / etc, since I won't be using the bike til next summer.
I live in Albany, NY but I am not quite ready to ask for help, just advice for now. But who knows if a month or two go by and I don't have this thing purring then I am not above asking for help .
- srankin
- Posts: 1085
- Joined: Fri Jul 14, 2017 8:45 pm
- Location: Spencerport, NY USA
- Been thanked: 21 times
Re: Just got a 1976 R60/6
Albany is a bit of a ride for me from Rochester. IF, you need an airhead friendly shop, Max, or my friend near me are available.
By the look of the pictures you won't need to do much work at all. Just remember to check the inside of the gas tank or as suggested pull the strainers. Even in a dry basement old gas will form varnish and gum things up. Good luck, St.
Re: Just got a 1976 R60/6
Replaced all the fluids. The gear oil, drive shaft oil, and final drive oil are all the same? I ended up using some synthetic 80/90 I had on hand.
Pulled the plugs, they were fouled. Cleaned them up and rested them on the head with solid ground contact. Turned it over, saw good spark.
After that I got her started and I been running her 10 minutes or so every day now. Sounding real nice. Couldn't help myself so I took a quick ride around the block. Feeling good.
Have an intermittent electrical issue where when I put on the headlight all the lights go out, including the running lights. It's not happening right now but it was for a few days.
Also I think one of the float valves is bad, I was slowly leaking fuel from the carb overflow valve. I popped off the carb cover and tested the valve and it needed to go just a little higher to cut off the fuel, so I ever so slightly bent the the float balloons down a touch. Seemed to do the trick but I foresee cleaning that carb out soon. But maybe there was just a little old gas gum in there and now that I am running plenty of fresh gas through it'll clean itself out.
It's getting colder around here, and I started the bike today and noticed a good amount of condensation dripping off the exhaust.
So my big question is, now that the bike is being stored in an unheated garage, so it'll be freezing and thawing many times over the winter, what do I do? Should I be starting the bike on the regular?