If you like our site, please consider joining our club!
By joining you will help ensure that we can continue to provide this service
JOIN HERE!

Search found 1182 matches

by wa1nca
Thu May 14, 2015 2:49 pm
Forum: Vintage (1948-1969) Motorcycles
Topic: Electrical issue
Replies: 13
Views: 3096

measure the voltage on the

measure the voltage on the battery when the engine is not running Start engine voltage now should go to at least 7 volts no higher than 7.4 If it does all is working ok It is not unusual that the red light will flicker at idle as the generator is putting out little current at idle It is just the way...
by wa1nca
Thu May 14, 2015 11:29 am
Forum: Vintage (1948-1969) Motorcycles
Topic: Electrical issue
Replies: 13
Views: 3096

Yes the are tied together on

Yes the are tied together on the circuit board in the generator assy
by wa1nca
Sat Mar 28, 2015 6:12 pm
Forum: Vintage (1948-1969) Motorcycles
Topic: R50 terminal block ?
Replies: 5
Views: 1516

6 set screws 1 set for

6 set screws
1 set for ground
2nd for taillight
3rd for brake light

by wa1nca
Wed Mar 25, 2015 8:34 am
Forum: Vintage (1948-1969) Motorcycles
Topic: R50 terminal block ?
Replies: 5
Views: 1516

The terminal block is held in

The terminal block is held in place by 2 cotter pins from the terminal block into the rear fender

by wa1nca
Wed Mar 18, 2015 4:55 pm
Forum: Classic (1970-25 years ago) Motorcycles
Topic: Timing plate/points screws stripped, need suggestions for removal
Replies: 10
Views: 3054

looks like enough room to get

looks like enough room to get a pair of small needle nose vise grips on them at a angle to get them started
by wa1nca
Fri Oct 24, 2014 2:46 pm
Forum: Vintage (1948-1969) Motorcycles
Topic: Anyone ever ship a bike to Europe !
Replies: 4
Views: 1154

R68S?? Maybe R69S

R68S?? Maybe R69S
by wa1nca
Wed Aug 20, 2014 3:34 pm
Forum: Vintage (1948-1969) Motorcycles
Topic: Cerakote ceramic coating
Replies: 6
Views: 1383

I used high temp paint on my

I used high temp paint on my r50 and it looked good for a couple of years but is fading now but easy enough to redo if I choose I did powder coat my r69s frame and jugs about 6 years ago and they still look new today Think I only paid about 250.00 for the frame jugs centerstand ect Kurt is correct 1...
by wa1nca
Sat Aug 09, 2014 12:26 pm
Forum: Vintage (1948-1969) Motorcycles
Topic: R26 electrical problem
Replies: 16
Views: 4477

if you run with your

if you run with your headlight on are you running with the high beam on or low?
try running with the headlight on low and then off if you can and see if the fuse still blows

by wa1nca
Fri Aug 08, 2014 3:47 pm
Forum: Vintage (1948-1969) Motorcycles
Topic: video clip - what do these rattles mean???
Replies: 22
Views: 5280

Steve is correct

Steve is correct
by wa1nca
Fri Aug 08, 2014 1:23 pm
Forum: Vintage (1948-1969) Motorcycles
Topic: Newbie - Found One Owner, Intact '66 R27 - Need Advice
Replies: 89
Views: 22681

this is where fuel is sucked

this is where fuel is sucked from air coming from the small hole on the intack side and is mixed with the fuel mixture srcew and then goes to the small hole in front of the throttle slide and this is the idile fuel mixture