By joining you will help ensure that we can continue to provide this service
JOIN HERE!
Which model had this gear cover
- malmac
- Posts: 796
- Joined: Sun Jun 29, 2014 2:10 am
- Location: Toowoomba, Australia.
- Has thanked: 1 time
Which model had this gear cover
Attached is a photo of the 2nd hand gear cover in the front and the original gear cover from my bike.
Someone has made an adapter plate to convert the older cover so it will accommodate the later model generator.
Which model does the front cover come from?
Mal
Toowoomba- Australia
- malmac
- Posts: 796
- Joined: Sun Jun 29, 2014 2:10 am
- Location: Toowoomba, Australia.
- Has thanked: 1 time
Re: Which model had this gear cover
How high should the breather plate rubbing surface sit proud of the machined surface which is outside the wear path?
Thank you in advance for your help people.
Regards
Mal
Toowoomba- Australia
- malmac
- Posts: 796
- Joined: Sun Jun 29, 2014 2:10 am
- Location: Toowoomba, Australia.
- Has thanked: 1 time
Re: Which model had this gear cover
Jan from Salis has told me .2mm, which rather surprised me, as it is not much.
But he is a good man and I never doubt his advice.
Thanks Jan.
Toowoomba- Australia
Re: Which model had this gear cover
Dave
- jwonder
- Posts: 784
- Joined: Wed Nov 23, 2016 7:50 pm
- Location: Long Island, New York
- Has thanked: 3 times
- Been thanked: 7 times
- Contact:
Re: Which model had this gear cover
The one with the tachometer drive cover missing is the upgraded timing gear cover. It was upgraded June of 1967 and the service bulletin is available in our library at https://vintagebmw.org/library_data/250.pdf. So, if your motorcycle is above the serial numbers listed in the service bulletin then that is the right one.
I am not sure why you have a adapter for the generator, because my generator from my 1967 R 69 S (with the tachometer plate) fits perfectly on my 1961 R 50 S timing gear cover without the tachometer plate. So it may be an older timing gear cover or the newer timing gear cover was setup for a 12 volt system? Not sure.
Vice President, Vintage BMW Motorcycle Owners
2022 BMW Friend Of the Marque
Long Island, New York
- malmac
- Posts: 796
- Joined: Sun Jun 29, 2014 2:10 am
- Location: Toowoomba, Australia.
- Has thanked: 1 time
Re: Which model had this gear cover
Thanks Jamesjwonder wrote: ↑Thu Sep 30, 2021 10:11 amMal,
The one with the tachometer drive cover missing is the upgraded timing gear cover. It was upgraded June of 1967 and the service bulletin is available in our library at https://vintagebmw.org/library_data/250.pdf. So, if your motorcycle is above the serial numbers listed in the service bulletin then that is the right one.
I am not sure why you have a adapter for the generator, because my generator from my 1967 R 69 S (with the tachometer plate) fits perfectly on my 1961 R 50 S timing gear cover without the tachometer plate. So it may be an older timing gear cover or the newer timing gear cover was setup for a 12 volt system? Not sure.
I also asked Jan at Salis but he was not sure. He suggested I contact Mark Huggett.
Mal
Toowoomba- Australia
- malmac
- Posts: 796
- Joined: Sun Jun 29, 2014 2:10 am
- Location: Toowoomba, Australia.
- Has thanked: 1 time
Re: Which model had this gear cover
Hi DaveDaves79x wrote: ↑Thu Sep 30, 2021 9:27 amI found that my R50's breather plate surface on the cover had been machined, I had to remove the circlip from the spring to get the plate to contact the rubbing surface. Works fine that way and later bikes did not even use the circlip. Just a b!tch to install with the engine in the bike!
Dave
If your cover was machined, should I assume it had been built up first with weld prior to being machined?
Apparently a N.O.S cover measured up at having a factory rise of only .2mm, so not much to play with before cutting below the surface of the machined land.
Mal
Toowoomba- Australia
Re: Which model had this gear cover
Dave