If you like our site, please consider joining our club!
By joining you will help ensure that we can continue to provide this service
JOIN HERE!

Bike wobble due to grooves in freeway

User avatar
davidmcctan
Posts: 35
Joined: Fri Jul 14, 2017 9:54 pm

Bike wobble due to grooves in freeway

Post by davidmcctan »

hi guys
My bike(r60/2) wobbles a little on the freeway.
I usually slow down to 50 mph and hug the tank with my knees.
I have avon roadsides 90 /90-18 on the bike
Will tightening the steering damper when you hit those grooves help , or is it just because the tires are small?
Any help appreciated
Attachments
20200512_095933.jpg
20200512_095933.jpg (997.26 KiB) Viewed 4280 times

User avatar
schrader7032
Posts: 9016
Joined: Fri Oct 27, 2006 3:00 am
Location: San Antonio, TX
Has thanked: 2 times
Been thanked: 29 times

Has the bike always wobbled?

Post by schrader7032 »

Has the bike always wobbled? What tires have you used in the past? Does the freeway have any grooves in it or has it been ground in a way to create lines in the pavement (eg concrete) running down the road.

You say Avon "roadsides"...do you mean Avon Roadriders AM26? Pictures of the tread on these tires show a bit of a central channel running around the circumference...not fully but some. Tires with some kind of central channel can move around if present to a pavement with grooves in it. I run Metzler Block C in front which have a major central groove, but I don't have any issues with wobbling...most of my roads are asphalt.

The steering damper is really only for slow speed running over very rough road. Using in a situation like this is covering up for something. I think you need to consider the tires and roads they're on, tire balance, air pressures (something like 32 front 36 rear), steering stem bearings, shocks, wheel bearings. How are the steering stem bearings? If you raise the front wheel off the ground and give the bars a slight push from the center position, do they speed up and prang off the stops or do they stay where you push them to?

Make sure the easy stuff is correct and go from there.
Kurt in S.A.
'78 R100/7 '69 R69S '52 R25/2
Fast. Neat. Average. Friendly. Good. Good.

User avatar
davidmcctan
Posts: 35
Joined: Fri Jul 14, 2017 9:54 pm

Yes, You are correct Avon

Post by davidmcctan »

Yes,
You are correct Avon roadrider
The road has been ground to have the lines in the cement. On asphalt, no issues whatsoever.

I will check all your notes above. Looks like a good start but thanks for clarification on what the steering damper is for

weh8127
Posts: 198
Joined: Tue Jan 16, 2018 11:28 am
Been thanked: 5 times

This should tell you what you

Post by weh8127 »

This should tell you what you need to know about steering dampers and more.

https://w6rec.com/friction-hydraulic-steering-dampers/
Bill Husted
Barre, MA USA
1963 R60/2 w/ 1955 Steib S500
1973 R75/5

User avatar
miller6997
Posts: 1185
Joined: Fri Oct 27, 2006 3:00 am

A very common complaint

Post by miller6997 »

Take Kurt's advice and eliminate the possible causes that he mentions. Then, if you explore past threads, you'll find a lot of discussion of this problem with grooved surfaces ("rain grooves"). It is most pronounced with tires that have a linear groove that goes all the way around the circumference of the tire. I always choose tires that don't have this feature. Metzeler and Heidenau both offer good options. The last time I checked, the preferred Metzelers were hard to find in North America, but Benchmark Works has a large selection of Heidenaus.
Jon Miller
'67 R69S
'13 F800GT
Altadena, California

sorbo1
Posts: 50
Joined: Fri May 16, 2014 6:45 pm

I have this problem on a

Post by sorbo1 »

I have this problem on a stretch of freeway near my home . The bitumen has been grooved to clear the water away . I run standard Heidenau tyres Front 3.25 x 18 K34 and Rear 3.50 x 18 K 35 . Tyre pressures Front 32 PSI and Rear 34 PSI . My bike is a 1961 R 69S at first it scared me . What I do now is relax and let the front move around a bit . I used to own a Yamaha TRX 850 with wide tyres and that was never a problem .I also have a 1991 Honda CBR 250 RR 4 cylinder 250 and it also has wider tyres than the R 69s with no reaction from the grooves . I have never used my steering damper . Hope this helps .

sheyma
Posts: 1
Joined: Wed Jan 17, 2018 8:57 pm

Re: Bike wobble due to grooves in freeway

Post by sheyma »

If your tires have the classic grooves that run parallel to the road, try gently weaving left and right in your lane, so that your tires are not parallel to the grooves as much. This may feel awkward at first, but after a while you will get the hang of it. It works and will become second nature after a while.
As always, pay attention to vehicles around you.
Steve
R50/2
R90/6

User avatar
jwonder
Posts: 784
Joined: Wed Nov 23, 2016 7:50 pm
Location: Long Island, New York
Has thanked: 3 times
Been thanked: 7 times
Contact:

Re: Bike wobble due to grooves in freeway

Post by jwonder »

I have Heidenau K36 on my R69S and they do NOT weave on the grooved pavement, they are perfect in every way IMHO.
Screen Shot 2020-07-05 at 3.58.12 PM.png
Screen Shot 2020-07-05 at 3.58.12 PM.png (1 MiB) Viewed 4245 times
BUT!

I have Heidenau K34 on my R51/3 and they weave on anything the bike can find. They are all over the place on grooved pavement. Steve is right that by performing a slight weave on the grooved pavement it stops the tires from grabbing the edges.
Screen Shot 2020-07-05 at 3.57.56 PM.png
Screen Shot 2020-07-05 at 3.57.56 PM.png (960.76 KiB) Viewed 4245 times
James Wonder
Vice President, Vintage BMW Motorcycle Owners
2022 BMW Friend Of the Marque
Long Island, New York

Captonzap
Posts: 87
Joined: Thu Aug 21, 2014 10:24 pm

Re: Bike wobble due to grooves in freeway

Post by Captonzap »

I had the same problem on my R51/3. While renewing the front tire, I checked the bearings, and they were a little loose. New bearings cured the problem.

User avatar
The Plunger
Posts: 269
Joined: Mon Sep 03, 2012 8:48 am
Location: West Des Moines, Iowa

Re: Bike wobble due to grooves in freeway

Post by The Plunger »

I had Metzlers that tossed me around. I switched to Mitas H02 with center lugs and it sure helped!
Brian
Brian
59-69

Post Reply