If you like our site, please consider joining our club!
By joining you will help ensure that we can continue to provide this service
JOIN HERE!

Original Enduro Saddle bag restoration

User avatar
oldtimers.si
Posts: 133
Joined: Mon Aug 18, 2014 11:00 am

enduro saddle bags brackets holders

Post by oldtimers.si »

hi,
we finish enduro saddlebags brackets holders version 2
you can install upper holder inside fenders
its ready for BMW R50 - R69S
( only for OLD Enduro Saddle Bags ABS )

regards,mec
Attachments
holders_enduro__bags_large.jpg
holders_enduro__bags_large.jpg (774.75 KiB) Viewed 3503 times

User avatar
skychs
Posts: 586
Joined: Fri Nov 25, 2016 2:12 pm
Location: Richmond VA
Been thanked: 1 time

lights

Post by skychs »

Did you ever add a dual bulb socket to your saddlebags for running and brake lights ?
If so want did you do

Tommy

I never did the dual filament swap for the Enduro bags. I simply ran the wires from the bag lights to the block for brake lights. Running lights are nice but I think extra brake lights are a better application. Maybe down the road.
chuck
1966 R60/2, 1967 R69S, 1975 R90S, 2020 R1250GSA

User avatar
skychs
Posts: 586
Joined: Fri Nov 25, 2016 2:12 pm
Location: Richmond VA
Been thanked: 1 time

lghts

Post by skychs »

Here are a couple photos of the bag lights on and off with the running lights. Not a huge difference during the day but noticeable at night.

Attachments
img_7976.jpg
img_7976.jpg (1.41 MiB) Viewed 3503 times
img_7977.jpg
img_7977.jpg (1.33 MiB) Viewed 3503 times
1966 R60/2, 1967 R69S, 1975 R90S, 2020 R1250GSA

User avatar
stagewex
Posts: 460
Joined: Sun Oct 26, 2014 8:18 am

Nice.

Post by stagewex »

Nice.
mike wex/stagewex
1969 BMW r60/2, US Model, 1995 BMW K75, 2006 Yamaha TW200, 2007 Ural Patrol, 1991 Honda XR250L

User avatar
skychs
Posts: 586
Joined: Fri Nov 25, 2016 2:12 pm
Location: Richmond VA
Been thanked: 1 time

Trim

Post by skychs »

While Im here ....
I'd like to replace the seal/trim on the lids. It looks like one side has been replaced but it's different from the other side. Any idea where I can get the lid trim?

Attachments
img_6743.jpg
img_6743.jpg (1.84 MiB) Viewed 3503 times
1966 R60/2, 1967 R69S, 1975 R90S, 2020 R1250GSA

User avatar
oldtimers.si
Posts: 133
Joined: Mon Aug 18, 2014 11:00 am

nice skychs , perfect send me

Post by oldtimers.si »

nice skychs , perfect

send me booth pictures , i look in my shop
maybe i find

regards,Mec

User avatar
skychs
Posts: 586
Joined: Fri Nov 25, 2016 2:12 pm
Location: Richmond VA
Been thanked: 1 time

Lids

Post by skychs »

I installed round rubber grommets in the holes that secure the pins in the lid. It makes the lid a little harder to install but I’m counting on it to keep my lid from blowing off in the wind. So far so good.
1966 R60/2, 1967 R69S, 1975 R90S, 2020 R1250GSA

Post Reply