By joining you will help ensure that we can continue to provide this service
JOIN HERE!
Airhead steering head bearing race pullers
Airhead steering head bearing race pullers
Greetings! I am waking up this bike that my dad bought in 1974. It sat indoors for around 10 years in total and had very good service history until that time. The head bearing action is a little notchy so replacement is justified. So far the only tool that I can see for the job of pulling the upper and lower hear frame races is an expensive puller for sale at the respected Boxer2valve company. Does anyone know of options to buy for less money or possibly a rental program out there?
Thank you. Keith in Scottsdale, AZ
- schrader7032
- Posts: 9052
- Joined: Fri Oct 27, 2006 3:00 am
- Location: San Antonio, TX
- Has thanked: 3 times
- Been thanked: 36 times
Re: Airhead steering head bearing race pullers
https://www.cycleworks.net/
'78 R100/7 '69 R69S '52 R25/2
Fast. Neat. Average. Friendly. Good. Good.
- srankin
- Posts: 1081
- Joined: Fri Jul 14, 2017 8:45 pm
- Location: Spencerport, NY USA
- Been thanked: 21 times
Re: Airhead steering head bearing race pullers
As for borrowing, maybe a member in your area will see this and get in touch. I have never checked out if the Vintage club has a membership list like the BMWMOA or I should say the MOA has the Anonymous book or list on line where people list services or help for towns. For example I list work space and working tools available. Want to ride up we could do it in an afternoon, LOL. Good luck. St.
Re: Airhead steering head bearing race pullers
- srankin
- Posts: 1081
- Joined: Fri Jul 14, 2017 8:45 pm
- Location: Spencerport, NY USA
- Been thanked: 21 times
Re: Airhead steering head bearing race pullers
Really the biggest pain in changing the bearings and races is installing the new races and assuring they are seated properly.
It is at that point a good tool makes sense. St.
- schrader7032
- Posts: 9052
- Joined: Fri Oct 27, 2006 3:00 am
- Location: San Antonio, TX
- Has thanked: 3 times
- Been thanked: 36 times
Re: Airhead steering head bearing race pullers
'78 R100/7 '69 R69S '52 R25/2
Fast. Neat. Average. Friendly. Good. Good.
-
- Posts: 200
- Joined: Fri Oct 27, 2006 3:00 am
- Has thanked: 1 time
Re: Airhead steering head bearing race pullers
- srankin
- Posts: 1081
- Joined: Fri Jul 14, 2017 8:45 pm
- Location: Spencerport, NY USA
- Been thanked: 21 times
Re: Airhead steering head bearing race pullers
I should smack myself on the forehead for not suggesting this. I do remember in past history BMW used grease that would harden over time in the steering heads.
So hopefully you haven't yet pulled the races? If you haven't, you can clean them very well of old grease, clean the bearings and with things dry no grease, spin the bearings in the races. You can feel the notches from where the rollers pounded into the race. If this happens, replace everything. Oh sometimes when the races have been cleaned you can also see the areas where the rollers have pounded into the race. if you see this, replace everything.
Sorry I didn't think of this before. St.
- cbclemmens
- Posts: 223
- Joined: Sun Apr 25, 2021 2:21 pm
- Location: Apollo, PA
- Been thanked: 6 times
Re: Airhead steering head bearing race pullers
Sometimes just over tightening the damper can give it that feel as well. Do what St. said and see.
Craig
BTW if you have to install new races, put them in the freezer overnight, heat the frame with a hot air gun or torch (careful not to damage the paint) and the should slip right in.
Re: Airhead steering head bearing race pullers
Thank you. Looks a lot more reasonable and Brooks Reams has a video tutorial using that tool.schrader7032 wrote: ↑Sun Mar 26, 2023 11:51 amWelcome to the forum! Maybe Cycleworks has something that will fit the bill:
https://www.cycleworks.net/