Darryl.Richman's picture

Day 1 - Newburgh, NY to Wellsboro, PA - 210 miles

Today turned out very well. The heay rains and subsequent really sticky weather went away and we had very pleasant riding weather: sunny but not hot or particularly humid.

There were two starts, the first at 7am at the Hilton Garden Inn hotel, the home base for registration and tech inspection. This hotel is immediately adjacent to a new, huge and very modern building for Orange County Choppers. Although I didn't have the opportunity or time to take a look, they were helping out riders in any way they could. Team HMS (1929 BMW R11) discovered that they didn't have a tool to remove the rather bizarre 8 sided jam nut that holds the left side rear wheel bearing to the frame. They went in and fellow at the counter had a correct sized hollow cut on their water jet, then welded to a backing plate with a 3/8s drive socket for a ratchet. (My bike has the same item, but I just use a big Crescent wrench. Now I'm envious of their special OCC tool!)

So, we were supposed to line up at the hotel for a sort of a parade start, each bike leaving at 15 second intervals beginning at 7:00:00. My time was actually supposed to be 7:01:30 (as compared to the 7:01:45) I reported earlier, but there was no official at the hotel to organize or oversee the event, and a few minutes after seven there was a general rush to the exits.

The second start was at 9am at the Motorcyclepedia Museum, about 4 miles away. In between was a hosted breakfast and time to view a bit of the enormous museum. They seemed to have one of every Indian and a heckuva lot of Harleys. I did see an R69S bunched together with some British and Japanese bikes in a corner.

The second start was only slightly more organized than the first, but eventually everyone got going. The route involved 12 pages of instructions, but was very clear and, other than missing a turn that occured 0.15 miles after the previous instruction, I had no difficulties.

The big bikes cruised along, although it was clear that some riders were more practiced with the arcane controls of their bike than others. Speaking of which, I must give a shout out to Peter Nettesheim, who explained to me how to double clutch my bike so that I didn't clash the gears everytime I shifted into second. With his clear explanation, it worked great, and I'm making a lot less noise and probably removing a lot less steel from the two second gears. (On these older BMW transmissions, 1st and 3rd are in constant mesh, but when you shift, you are actually moving second gear on the output shaft back and forth and forcing it into mesh with its counterpart on the input shaft.)

The R52 ran great and did the entire route with little drama. Maybe the biggest problem was that one of the knobs on my routebook holder came loose. Don Cameron successfully sealed the nose of the final drive, so that messy little leak is over with. Samantha followed me the entire day, and I really appreciate that. Even after she had drained her camera's battery, she was still back there running her flashers and keeping the regular traffic back a bit.

Tomorrow is a long day, 320 miles, and it also includes a 62 mile stretch of I-90 from the east side of Cleveland to Sandusky, OH, our destination. There is an option given to us by the organizers to declare tomorrow morning that we will end just before Cleveland, and our chase vehicles can then transport us to Sandusky; but it isn't a free ride, we lose the 60 points that represent those miles. I have decided to go for the full ride instead.

At the start, before 7am
At the start, before 7am81.77 KB
At the finish, after 3pm
At the finish, after 3pm104.29 KB


Day 1

Bengt Phorqs's picture

Well I'm sure that you are glad to finally be underway. I'm watching with interest and I'm also following Round The World Doug on his 1929 Indian Scout. Says he carrying everything with him and no support vehicles, but he has a huge following and I'm sure will have no shortage of help along the way. I'm confident that Airheads Rule! -Mike

Final Drive Sealing

David Brick's picture

What did Don do differently that this time successfully sealed the nose on the final drive?

Motorcycle Cannonball

Tony Greco's picture

Ride Hard, Ride Free, Ride very, very Fast!! Smile. Be safe!


lubbeth's picture

We'll be looking for you, in Monroe. If you need anything brought to you, from Madison, I can do that. We'll be there on a 1955 R50 and a 1975 R90/6. If you can post the route the night before I'd like to stand by the side of the road and take pics/videos as you go by. We're are the Tom and Terry of Tom, Terry and Daniel on the side of the Sprinter. Daniel is at Univ of Mn by now, with the R69US. I think he is likely the only freshman there that rode a R69US (or any vintage BMW) to get to college. It's garaged there now.


Thanks for the support, everyone!

Darryl.Richman's picture

Don thoroughly cleaned both cast surfaces and the aluminum gasket and then gooped them up MORE, including the bolts. Then we let the whole thing set for about 4 hours with the front of the bike jacked up a bit to keep the gear lube away.

Today's route looks like more US-6 in PA, then assorted side roads until we get on I-90. It's about 9 hours at a 35mph pace to get to the end.

--Darryl Richman
"Bling is not made in Germany" --OTL, 12/05

Cannonball Milwaukee to Anamosa

Bruce Pickering's picture

Nice to see that you are underway and pray that things are going well. I live just 30 miles from your Monday lunch stop here in Monroe WI and will see you there. It would be nice to know your route so we can see all the bikes underway. I hope you can post it here. If they got it right it would be Hwy 59. That starts in Milwaukee and ends in Monroe. It goes through the beautiful Kettle Moraine area and beyond with lots of gentle hills and big "sweeper" us riders love and no large cities to go through. We'll see you in Monroe.

Sprinter making it two to the finish

Monte Miller's picture

Very pleased to hear your "loaded" Sprinter is back among the living. That's one less iron butterfly in your belly. Remain Calm-Carry On. -Monte

Go, Darryl, Go

Jim Brown's picture


I'll be avidly following your progress westward, and looking forward to your posts. Looks like your side biz (Darryl's Dead Bike Storage Wink has proven to be a viable enterprise! Best of luck on your ride.


BTW, you REALLY should repaint that R90S Daytona Orange when you get back to Santa Cruz. Just sayin'

A good start after all

Guy's picture

Happy to see and read that overall, it was a good start. Great of Sam to be your 'bodyguard' for that part of the trip.
9 hours today though.... fingers crossed!


From you European fans

guest's picture

Good luck Darryl! Very successful start Smile Best wishes from Czech Republic

Jana & Peter

Ride steady, drink lots of

guest's picture

Ride steady, drink lots of water unless it's raining, and beware of lurking 101 Scouts.

Following With Interest

David Haley's picture

Atta boy Darryl.
David H.

Post new comment

The content of this field is kept private and will not be shown publicly.
CAPTCHA stops spam by preventing automated "bots" from accessing this site.
Enter the code without spaces and pay attention to upper/lower case.
Darryl.Richman's picture

One last preview

Here's a quick preview of the R52 in action:


That is very sweet!

David Brick's picture

That is very sweet!

Welcome soon to Ohio

Jim Shaw's picture

Looking forward to seeing you and some of the other riders at your hotel in Sandusky. I'll try to remember the camera. Hope all is purring along like it should along 6 in PA.

If there's anything I can help with during that stop, let me know.


Fred Ellenberger's picture

See you when you get off the high speed ferry in Milwaukee Sunday afternoon,
Good luck on the road, looks like a super bike
Fred Ironbutt 25910

cannonball run to sandusky

guest's picture

anyone know what hotel in sandusky, would love to ride over sun am to see this--live about 60 miles east of there. Thanks.

Help in ID and OR

Larry's picture

Good to see you on the way after so much preparation. With the initial difficulty out of the way, it can only get better as the miles drift away. I and many others are along the route cheering you on. Please feel free to ask if assistance is needed from the Mt Home through K-Falls segments. I can cover that stretch with parts run or a pickup. 5zero9, 5two1,5eightthree5

Southern Wisconsin

jeff dean's picture

I wish I knew when and where you were coming through Wisconsin.

I would have fired up my R60/2 and ridden down to meet you!

Post new comment

The content of this field is kept private and will not be shown publicly.
CAPTCHA stops spam by preventing automated "bots" from accessing this site.
Enter the code without spaces and pay attention to upper/lower case.
Darryl.Richman's picture

Here We Go!

Things are looking up! The Sprinter spent Tuesday and Wednesday at a local shop. They replaced the fuel filter and the "turbo resonator" (a device that muffles the output of the turbocharger, is made of plastic, and has a poor reputation because it splits along a molded seam, as mine did), and now the Sprinter runs fine again.

Our hosts in the greater Newburgh area, my friends Jeff and Samantha, let us borrow their pickup and trailer to take the R52 down to the hotel on Wednesday to get registered and put the bike through tech inspection. It was raining cats and dogs, so I decided not to do the 42 mile test ride. Instead, we hung around a bit and I was able to pigeonhole Lonnie Isam, the organizer, and get a few details worked out.

Jeff Wu had a last minute crisis and couldn't make it out to New York, so Samantha is taking over for him, taking some video mounted from her R1150R. She will do this out to Milwaukee and then Jeff will rejoin the team in Sturgis.

This morning we got the Sprinter back and we loaded things up and reorganized so that the bike can be loaded and unloaded without having to unload a lot of other stuff. We got out to the hotel around noon and after a while of meet and greet, I took the R52 out on the test loop. Things went very well: I was able to use my home made roadbook holder easily and the bike ran well. Samantha said, and I also saw on my electronic speedo, that the bike attained a bit over 60 mph at its fastest, which is very adequate. I have to tweak the front tire circumference in the speedo as it lost a couple tenths over the course of 40 miles. The only real problem was the rear brake adjuster knob fell off, but Sam saw it and grabbed it. (Losing that means not having any rear brakes.) Oh, and the large doe in the middle of the road we saw as we rounded a downhill righthander, so I was trying capture some momentum for the coming uphill.

On return, the bike had a couple of its persistent weeps in evidence. Where the cap on the front of the final drive meets the body, there is a flaw in the mating surface, and it usually drips a bit of oil. This makes a terrible mess and oils the sidewall (but not the tread) of the rear tire. So we pulled it off, cleaned things up, and then tried to goop it up a bit more. Tomorrow we will find out how well we did. There's also a small weep from where the magneto mates to the top of the crankcase, which results in a bit of oil on the right floorboard, which is also an annoyance. I'm inclined to ignore that unless we have some further reason to have to remove the mag, which seems to be performing very well (as is the integral generator, which powered my headlight and taillight for the entire trip).

There was a riders' meeting in the afternoon, which went over a variety of topics, then the opening dinner banquet, which was very nice and lots of fun. At the end of dinner the rules and regs were emphasized and then a lot of people retreated to the bar, but we headed back to Sam's house for an early evening.

Tomorrow morning we have to be lined up at the hotel, ready to go on our assigned 15 second intervals (mine is 7:01:45). We are actually only riding 4 miles over to the Motorcyclepedia Museum, where there will be a two hour breakfast and display for the public. Then we line up and leave at 9am. 210 miles later, hopefully, we will pull into Wellsboro. The route sheets indicate that much of tomorrow's ride will be over US-6, especially in Pennsylvania. A lot of questions will be answered tomorrow, I hope I like them.


Cannonball Run

Matz Rosenquist's picture

Hi Darryl!

Today's the day if I'm right! Good luck on you, the bike, your team and the Sprinter!
I'll keep a close watch on your blog!


Darryl, the very best of luck

Andy Dukes's picture

Darryl, the very best of luck from Andy Dukes back in the UK. Looking forwards to reading about your exploits! Let's talk in around, say, 17 days time!

We're watching you...

Stefan Koch's picture

Looking forward to following you on this journey... I'm envious!

Vaya Con Dios

Post new comment

The content of this field is kept private and will not be shown publicly.
CAPTCHA stops spam by preventing automated "bots" from accessing this site.
Enter the code without spaces and pay attention to upper/lower case.
Darryl.Richman's picture

Made it to NY

Well, we made late last night to NY. Crawling up all those hills in the Alleghenies at about 40mph really had me watching my mirrors. The Sprinter is at a shop this morning and I'm hoping to hear back soon what the problem is. In the meantime, Steve and I are recovering from four long days of sitting still. Don will be here in another couple hours.

Jeff Wu won't be able to be here at the start, so we are abducting our hostess, Samantha Lucas, to be our camera bike rider through to Milwaukee. Team Boxer Rebellion is rolling with the punches!


Cannonball Run

rhmossbeach's picture


Good to see you've made it to NY and about to begin the real adventure!

Groeger's breakfast was pretty quiet last Sat.

Best of luck(and weather) and trust all the time put in is rewarding all of you!

Randy H


John Landstrom's picture

I bet your Sprinter lost the Turbo, probably a split the turbo collector box, I'm on my 3rd one in 100,000 miles. It's gotten to where I carry a spare one.

Cannonball Run

John Cox's picture

Wishing you all the best from Australia.

Cannonball Route

rgethin's picture

What route will be used across PA? I am thinking that I could ride south and watch/follow as the bikes cross PA. I live just west of Binghamton, NY


Dave Scott's picture

You will probably have better luck with your 1928 BMW then the van. It's kind of wild but true. Is the route going through upper or lower WY?


brown3459's picture

I think the route is a secret until revealed to the riders each morning.
Best of luck Darryl.

Post new comment

The content of this field is kept private and will not be shown publicly.
CAPTCHA stops spam by preventing automated "bots" from accessing this site.
Enter the code without spaces and pay attention to upper/lower case.
Darryl.Richman's picture

The Adventures Have Begun

Well, Steve Woodward (my chase van driver) and I are in South Bend, IA this morning, after three long days of driving. Our goal is to land, late tonight, at my friends' house in Amenia, NY.

However, the trip has not been without incident. The Sprinter, which has its quirks but has not given me any troubles, put up an engine check light when I fired it up Friday morning to leave. So, we drove over to the shop that has worked on it and they the codes -- two weak glow plugs (out of 5). They reset the code and said it shouldn't be a problem for us unless we had to cold start it on a cold morning.

So, we were on our way. Over the Sierra Nevada mountains and into Reno for fuel. But out on the highway again, the engine check light popped on for no discernable reason. Then, the van lost power and went into what is referred to on the Sprinter forums as "limp home mode", which limited us to about 65mph and pretty slow acceleration (even for the Sprinter). We stopped in Salt Lake City for the night but couldn't find anyone who could even read the code on Saturday morning of a three day weekend. So, we limped along to North Platte, NE and South Bend today and hopefully NY tonight. Tomorrow we will try to find a shop with some Sprinter savvy so Steve doesn't have to limp all the way back across the continent.

Otherwise, things are going well -- neither of us yet wants to murder the other! Don Cameron, our chief mechanic, is riding his Gold Wing from Deming, NM. Last night he stopped in Kankekee, IL, leaving him 800 miles from Amenia. He'll do most of that today, we might even see him on I-80, but will stop for the night somewhere short of Amenia, and will roll in tomorrow.

img_0645_resize.jpg195.7 KB
img_0651_resize.jpg146.62 KB
img_0707_resize.jpg172.89 KB
img_0713_resize.jpg133.24 KB
img_0718_resize.jpg128.05 KB


Good Luck

Jack Duggan's picture

Thanks for the blog. Pretty exciting, the start is almost here. I look forward to hearing about the trip as you make it. And on the bike you don't have to worry about dummy lights and computer readings. I guess we didn't have as much information years ago that we do today. It may have been easier that way. But keep the info flowing on the internet.

Maybe I'll be there to see the bikes at Cotati.

Relative German Reliability

miller6997's picture

Won't it be a hoot if the ancient BMW comes through unscathed and the Mercedes craps out?


'67 R69S
'05 R1200RT

Post new comment

The content of this field is kept private and will not be shown publicly.
CAPTCHA stops spam by preventing automated "bots" from accessing this site.
Enter the code without spaces and pay attention to upper/lower case.